It is important! The specification is a general specification.
It is necessary to consult with the Technical Department of BI. J. Technologies, before performing the work.
Be sure to follow the relevant standards.

1. The balcony should be thoroughly cleaned of any dirt, construction residue, mortar, paint, etc., for a strong, clean and stable concrete surface.

2. In the connection between the floor and the console wall and between the floor and the separation belt of the living room, cut with a disc
Concrete leaks (concrete), excess concrete and the like, and slit until a clean and clean corner is obtained.

3. In the above places, a groove should be made with a double disc at an angle of 45 °, 1 cm wide and 2-1 cm deep.
At any circumference and save PU-40 Rolka. As much as possible and clean up a struggle. You can perform a + b slot. G-cement.

4. If no groove is made around, a small cementitious roll made of 1: 2 sand cement should be made in a BG catcher. Primer should be applied
My heart. G Bond 2 Without dilution.

5. In the above mixture, segregations can be closed for holes in the wall and railings if required. All rollers
And the repairs will be cured with the dose and speed required to prevent dehydration and "burning" the mixture
From the heat and the dryness.

6. Make a slot 1X1 or 2X1 between the receptor and the concrete. 

Execution instructions
Apply primer My heart. G PU-40 In the slot and seal the PU-40. This ensures sealing of the gutter regardless of the element being connected. 

We must wait for drying and the next day to implement it on the infrastructure Me. J. Radix Primer 2000 through
IRLES spray / brush / roller in the amount of 250-300 g / m2 and wait for drying for about two or three hours
Depending on weather conditions.

After primer drying, apply Me. J. Super Reflex 2001 In two layers in a quantity of
2.5 kg per square meter (in any case involving a planner or a sealant consultant must follow his instructions). Wait -1.5
At least 24 hours to dry, depending on weather conditions. When the temperature of the concrete surface drops below
10-° C, it takes longer to dry the material.

I have to reserve with my help. J. 2001 Super Reflex with an X-NMX Intrinsic Network
Throughout. The sealing height will be up to all the layers 5 + cm under the stone or until connected with
The stone.

The paving shall be carried out according to the adhesive specification for porcelain granite on stabilized sand.

Most of the:
Fugues must be filled with Acrylic BJRO.

When preparing the balcony for sealing, a separation belt must be maintained between the room and the balcony.

Make sure that the flooring of the inner porch rises with the mortar on the belt without sand, so there will be no contact between
The sand outside the sand inside (in the case of paving on the sand).

Make sure the sand pavement falls below the belt 1-0.5 cm.

Make sure that the belt is well-connected with the outer walls and in case it only touches the block
Perform a bandage between the belt and the block just as it does between a pillar and a block in the walls (for prevention
Thermal crack).

In the case where the balcony is molded with a railing, and above the rail-line blocks, be careful in the block bar
First, paste with cement-rich mortar and perform a joint bandage (as in a casting break) between the block
Concrete. The bandage will be fromBJ. Radiant 701 + Intrinsic network.

The sealing must pass 5-10 cm above the final height of the panel or in case of stone cladding under half
The height of the lower stone. Of course, the infrastructure for sealing on beams / railings is black cement mortar.
All of the above is only a recommendation, given according to the best knowledge we possess and our extensive experience.
However, because the work is not under our control, the factory's warranty is limited to the quality and quality of the product only.
The operation must check compliance with its needs and proper performance of the work.


logo bg bond
BJ (Israel) Technologies Ltd., Kibbutz Beit Guvrin, moving post to Lachish South, 79370 //

Copyright © BG Bond. All rights reserved
logo ashtrum3